A Wheel Cylinder Replacement cost in Oakland Park in 2024

The average cost for a brake wheel cylinder replacement with CarAdvise is $145 and the range is generally between $69 and $320.

Get expert advice, find shops, schedule, approve, & pay for any service - guaranteed to be lower than in-store retail price.

Get your vehicle's inside scoop without the mumbo jumbo.

Lower than retail price

Guaranteed or 5% back

We've got your back

12k/12mo Warranty

Peace of mind

14-Day Assurance

AVERAGE COST IN Oakland Park

A Wheel Cylinder Replacement costs by shop in Oakland Park.

CarAdvise Customers save an average of $29 on A Wheel Cylinder Replacement.

POPULAR VEHICLES

Average cost of A Wheel Cylinder Replacement for popular vehicle models in Oakland Park:

Car Model

Avg. cost

$50

THE IMPORTANCE OF A Wheel Cylinder Replacement

What is a wheel cylinder and how does it work?

A wheel cylinder is a component of a drum brake system. Unlike a disc brake system, where a pair of brake pads squeeze together against the outside of a spinning disc to slow and stop your vehicle, a drum brake system relies on a pair of brake shoes suspended inside a bowl-shaped drum. When you press on the brake pedal, the wheel cylinder responds to hydraulic pressure, forcing the brake shoes against the inner wall of the drum to create friction. There is one dual-piston wheel cylinder in each drum.

COMMON SYMPTOMS

Signs that a wheel cylinder needs to be replaced

While most late-model vehicles feature four-wheel disc brakes, a number of makes and models are still made with rear drum brakes. If your car or truck is fitted with drum brakes and you notice any of the following signs, you might need to schedule wheel cylinder replacement:

Your brake pedal feels soft or spongy due to an internal leak

The brakes do not respond as usual

You hear a scraping or grinding noise from a stuck wheel cylinder

You see an oily fluid leak on the ground just inside one of the rear wheels, on the inside of the tire, or on the drum backing plate

This text is only for demo

FREQUENCY OF INSPECTION

How does a technician perform A Wheel Cylinder Replacement ?

When a wheel cylinder fails, it is usually recommended to replace the component on each side of your vehicle, especially when additional drum brake service is being done. To perform the repair, a mechanic will first need to lift and suspend your vehicle safely off the ground and remove the rear wheels and tires to access the brake drum system. Once that is in order, your mechanic will follow these general procedures to replace a wheel cylinder:

  • Remove the brake drum
  • Detach the brake shoe springs and retainers and remove the shoes
  • Disconnect the hydraulic brake line from the wheel cylinder, taking care to avoid damage to the tubing
  • Unbolt the wheel cylinder from the backing plate and dislodge the cylinder
  • Clean the wheel hub and backing plate
  • Install a new wheel cylinder and reattach the brake line
  • Install brake shoes, hardware, and drum
  • Bleed air from the brake lines
  • Install the wheels and tires and lower vehicle
  • Actuate the brakes and test drive the vehicle to verify the repair (and to bed in the new brakes if shoes and drums were replaced)
  • Note that, on some vehicles, it may also be necessary to disconnect the battery when servicing the brakes

OTHER QUESTIONS CUSTOMERS ASK

What happens when a wheel cylinder goes bad?
The brake system on your vehicle is made up of a network of tubes, called “brake lines” that run along the underbody to each wheel. When you press on the brake pedal, a pump (the “master cylinder”) puts pressure on the hydraulic oil in the brake lines. That pressure is used to actuate the wheel cylinders (in the case of drum brakes) and force the brake shoes against the inside of the drum. If a wheel cylinder fails, either there will be insufficient force to stop your vehicle properly or the brake shoes will not release fully from the drum and cause the wheel to drag. Either situation can become unsafe, especially since the brakes are the most important safety feature of your vehicle.
How do you check a wheel cylinder?
A wheel cylinder is hidden inside of the brake drum where the brake shoes are located. While there are some external signs that a wheel cylinder has gone bad - such as a visible fluid leak, a dragging wheel, or a failure to stop properly - the only way to tell for sure is to have it inspected. To do that, a technician must raise and support your vehicle, remove the wheels and tires, and take off the brake drum to access the wheel cylinder.
Should wheel cylinders be replaced in pairs?
It is technically possible to replace only one wheel cylinder. However, it is recommended that wheel cylinders be replaced in pairs, especially if you are having other drum brake service done at the same time, such as brake shoe replacement. If one cylinder fails, it is likely that the other will fail in time as well, or that the response of a mixed pair of old and new wheel cylinders might cause irregularities when braking.

This is demo Question

This is demo Answer

Compare discounted prices upfront at over 26,000 shops nationwide.

Finding a trusted shop has never been easier. We've partnered with the largest brands in auto maintenance to give our customers the biggest network to choose from.

+ More

Join the world's largest consumer fleet.

Over 1.5 Million already have.