Mass Air Flow Sensor Replacement costs by shop in Shakopee.
CarAdvise Customers save an average of $48 on Mass Air Flow Sensor Replacement.
Average cost of Mass Air Flow Sensor Replacement for popular vehicle models in Shakopee:
Avg. cost $169
Avg. cost $327
Avg. cost $240
THE IMPORTANCE OF Mass Air Flow Sensor Replacement
What is a mass air flow sensor and how does it work?
A mass air flow sensor (MAF) is an electronic device installed in your engine’s air intake system. This sensor monitors the volume of air that goes into your engine across various operating conditions. On some vehicles, the mass air flow sensor also detects the incoming air temperature and pressure as well. The information from these readings is sent to the main engine computer, the Engine Control Module (ECM), where it is used to control factors such as the amount of fuel injected into the engine cylinders, the ignition and camshaft timing, and more, all to help your engine run as efficiently as possible.
How do I know if my vehicle needs the mass air flow sensor replaced?
When a mass air sensor fails, the performance of your vehicle can suffer. Under certain conditions, it can also cause engine damage. Reduced fuel economy is likely as well. Your mass air flow sensor might be bad if you notice one or more of the following signs:
A reduction in fuel efficiency
A drop in engine power
Your engine stalls
Hesitation on acceleration
This text is only for demo
FREQUENCY OF INSPECTION
How does a technician perform Mass Air Flow Sensor Replacement ?
The mass air flow sensor is mounted in the air intake ducts that lead to the throttle body on top of your engine. It is often necessary for a technician to remove engine covers, shields, ducts, and other components for access to this component. The technician will also disconnect the negative terminal on your battery, taking care to preserve the vehicle computer memory. From there, the technician will take the following general steps:
Disconnect the electrical connecter attached to the mass air flow sensor
Remove the fasteners that attach the sensor to the ducts in which it is mounted
Dislodge the sensor and remove it from the ducts
Insert and fasten the new mass air flow sensor
Reconnect the wiring harness plug
Reinstall all components that were removed for access and the battery cable
Clear any diagnostic trouble codes (if necessary)
Test drive your vehicle to allow the sensor to reset itself (and to verify the repair)
OTHER QUESTIONS CUSTOMERS ASK
Is it better to clean or replace a mass air flow sensor?
Whether to clean or replace the mass air flow sensor is a decision best left to a qualified technician. Mass air flow sensors can show incorrect readings due to failure of the sensor itself, as well as the sensor simply being dirty. A technician may attempt to clean the sensor first and then recheck the sensor feedback with a scan tool, or the technician may recommend replacing the sensor if it is clear that the existing sensor is damaged or has internal issues.
How many miles does a mass air flow sensor last?
A mass air flow sensor may last anywhere from 80K-200K miles. However, this depends greatly on how well the engine air filter is maintained and in what type of environment the vehicle is driven. A vehicle used primarily in dusty or off-road environments may require cleaning and/or replacement of the mass air flow sensor more frequently.
What happens when a mass air flow sensor goes out?
If your mass air flow sensor goes bad, the Engine Control Module (ECM) will be unable to determine how much fuel is needed at any given time for your engine. That means your engine can run rich (too much fuel) or too lean (too little fuel). Both are detrimental to your engine. But if it runs lean for too long, serious engine damage can occur.
This is demo Question
This is demo Answer
Compare discounted prices upfront at over 26,000 shops nationwide.
Finding a trusted shop has never been easier. We've partnered with the largest brands in auto maintenance to give our customers the biggest network to choose from.
Our digital platform is designed to make maintaining and repairing your vehicle a breeze – from conveniently scheduling services, finding shops in the area, approving work remotely or getting free expert advice so you can be confident about any decision.
How much does CarAdvise cost?
There’s nothing to pay up-front; you simply only pay for repairs or services that you approve.
Are there any additional fees?
Nope, no funny business here—just get the job done and pay for what you approve. It really is that simple.
Are there shops available in my area?
With our handy nationwide network of over 26,000 shops to choose from and free sign-up – you can rest assured your car is in good hands.
How does CarAdvise pricing work?
With CarAdvise, you don’t need a fleet of 100,000 cars to get an amazing deal on car services. Our discounted prices are guaranteed to beat any other retail options – so why spend more? On average customers save 15-40% when they choose us – that could mean hundreds saved in just one service job.
At CarAdvise, we believe life is unpredictable and if you need to reschedule or cancel an appointment – no worries! We promise there’s never any penalty for missed appointments.
What shops do you work with?
We’ve partnered with the best in the industry such as Firestone, Pep Boys, JiffyLube, Canadian Tire, NTB, Meineke, Tire Kingdom, AAMCO, Monro, FCA dealerships and many independent shops across the country.
How do I sign up?
Ready to join the party? Just a few clicks and you’ll be all set – create your account now. You can easily create your account here.
How do I get more help?
Just email us at [email protected] or give our friendly team a ring at (844) 923-8473 and we’ll be sure to lend you the helping hand you need.