An Oxygen Sensor Replacement cost in Warwick in 2023

The average cost for an oxygen sensor with CarAdvise is $279 and the range is generally between $124 and $547.

Get expert advice, find shops, schedule, approve, & pay for any service - guaranteed to be lower than in-store retail price.

Get your vehicle's inside scoop without the mumbo jumbo.

Lower than retail price

Guaranteed or 5% back

We've got your back

12k/12mo Warranty

Peace of mind

14-Day Assurance


An Oxygen Sensor Replacement costs by shop in Warwick.

CarAdvise Customers save an average of $56 on An Oxygen Sensor Replacement.


Average cost of An Oxygen Sensor Replacement for popular vehicle models in Warwick:

Car Model

Avg. cost


THE IMPORTANCE OF An Oxygen Sensor Replacement

What is an oxygen sensor and how does it work?

An oxygen sensor (O2 sensor) is a device fitted into the exhaust system of your vehicle to detect the amount of unburned oxygen that is present in the exhaust gases coming from your engine. During combustion, your engine burns a mixture of air and fuel inside the combustion chambers. When that air/fuel ratio is out of balance, excess amounts of unburned fuel or unburned oxygen escape through the exhaust.

To correct these conditions, a vehicle has two to four oxygen sensors mounted near the exhaust manifold or on the exhaust pipe near the catalytic converter. These sensors read the amount of oxygen present in the exhaust and send data to the engine’s computer (the Engine Control Module, or ECM). The ECM analyzes this data and adjusts the air/fuel mixture for optimal performance and fuel economy.


What are the signs that an oxygen sensor needs to be replaced?

If one or more of the oxygen sensors on your vehicle is faulty, the following signs are likely:

The check engine light comes on and a diagnostic scan reveals a trouble code related to an oxygen sensor

Your engine idles roughly

Fuel economy drops

You notice a rotten egg smell coming from the exhaust

This text is only for demo


How does a technician perform An Oxygen Sensor Replacement ?

To replace a faulty oxygen sensor in your vehicle, a technician will first need to diagnose which sensor is bad and where it is specifically located. Every vehicle is different, so research is needed to locate the proper sensor. Your vehicle may also need to be lifted and supported off of the ground for access to the sensor. With the vehicle in position, the technician will take the following steps:

  • Unplug the wire connecting the oxygen sensor to the vehicle harness
  • Unscrew the oxygen sensor from its mounting location. The sensor is often difficult to remove and may need the help of penetrating oil or heat to prevent it from breaking off in its mount
  • Verify that the replacement sensor is correct and add anti-seize compound to its threads
  • Insert the new sensor into its mount and tighten
  • Plug in the sensor wire, making sure that the pigtail is routed properly
  • Lower your vehicle
  • Using a scan tool, clear the trouble code from the ECM


Can I replace an oxygen sensor myself?
The procedure to replace an oxygen sensor on many vehicles is not an extremely complicated one. That said, it is not always easy. First of all, a vehicle usually needs to be safely lifted and supported off of the ground for access to an oxygen sensor. Then there is the difficulty accurately diagnosing which sensor needs to be replaced (something that requires a diagnostic scan tool) and determining where that specific sensor is located. Dislodging the sensor from its mounting location is also tricky; an oxygen sensor is often stuck in place and too often breaks before loosening up.
What happens if an oxygen sensor is not replaced?
If an oxygen sensor fails and is not replaced, one thing that will happen is that your engine’s computer will not be able to accurately set the air/fuel mixture for combustion. Poor fuel economy and higher emissions will result. Damage to the catalytic converter is also possible - and costly. And your vehicle will probably not pass an emissions test.
What causes oxygen sensor failure?
An oxygen sensor usually goes bad because it becomes contaminated with a buildup of combustion byproducts, such as oil and soot. Sometimes, oxygen sensors get gummed up due to the use of cheap fuel. Even engine coolant that leaks into the combustion chamber through a faulty seal can also cause contamination.

This is demo Question

This is demo Answer

Compare discounted prices upfront at over 26,000 shops nationwide.

Finding a trusted shop has never been easier. We've partnered with the largest brands in auto maintenance to give our customers the biggest network to choose from.

+ More

Join the world's largest consumer fleet.

Over 1.5 Million already have.

Questions? We've got answers.

Our digital platform is designed to make maintaining and repairing your vehicle a breeze – from conveniently scheduling services, finding shops in the area, approving work remotely or getting free expert advice so you can be confident about any decision.

There’s nothing to pay up-front; you simply only pay for repairs or services that you approve. 

Nope, no funny business here—just get the job done and pay for what you approve. It really is that simple.

With our handy nationwide network of over 26,000 shops to choose from and free sign-up – you can rest assured your car is in good hands. 

With CarAdvise, you don’t need a fleet of 100,000 cars to get an amazing deal on car services. Our discounted prices are guaranteed to beat any other retail options – so why spend more? On average customers save 15-40% when they choose us – that could mean hundreds saved in just one service job.

Learn More

At CarAdvise, we believe life is unpredictable and if you need to reschedule or cancel an appointment – no worries! We promise there’s never any penalty for missed appointments.

We’ve partnered with the best in the industry such as Firestone, Pep Boys, JiffyLube, Canadian Tire, NTB, Meineke, Tire Kingdom, AAMCO, Monro, FCA dealerships and many independent shops across the country.

Ready to join the party? Just a few clicks and you’ll be all set – create your account now. You can easily create your account here.

Just email us at [email protected] or give our friendly team a ring at (844) 923-8473 and we’ll be sure to lend you the helping hand you need.