A Flywheel Replacement cost in Bryan in 2024

The average cost for a flywheel replacement with CarAdvise is $585 and the range is generally between $360 and $1012.

Get expert advice, compare prices, schedule, approve, & pay for any service at your favorite shops - guaranteed to be lower than in-store retail.

How CarAdvise Works


Find 400+ services from a network of trusted shops and book appointments in seconds.


Approve or decline an itemized list of services and costs before any work begins.


Pay securely and enjoy exclusive discounted rates and a hassle-free checkout experience.


A Flywheel Replacement costs by shop in Bryan.

CarAdvise Customers save an average of $117 on A Flywheel Replacement.


Average cost of A Flywheel Replacement for popular vehicle models in Bryan:

Car Model

Avg. cost


Maintenance as it's meant to be.


Never overpay for car maintenance. Compare and select from discounted prices across 26,000+ trusted shops nationwide.


Ignite your auto knowledge. Gain invaluable insights into maintenance schedules, service clarity, and obtain expert advice.


Bypass the stress of negotiations. CarAdvise simplifies your car care journey for an effortless experience.

THE IMPORTANCE OF A Flywheel Replacement

What is a flywheel and how does it work?

A flywheel is a large flat metal disc that is bolted to the rear of an engine’s crankshaft in a vehicle with a manual transmission.

The flywheel helps to transfer the power of your engine to the transmission. It spins with the crankshaft and interacts with the clutch disc to engage the drive wheels. The flywheel stores energy to supplement engine torque and help to balance out the power stroke of each cylinder as it fires. And it helps to reduce engine vibrations. The flywheel also has a series of teeth cut into its outer edge. These teeth mesh with the starter, allowing the starter motor to spin the crankshaft during the startup process.


How do I know if my vehicle needs a flywheel replacement?

A flywheel that is worn or damaged will display a variety of symptoms, depending on what has gone wrong. When a clutch assembly wears out, the face of the flywheel will commonly wear out as well. The flywheel can also become warped from excessive heat. The teeth on a flywheel can also break off and prevent proper articulation with the starter.

If you notice one or more of the following signs, your vehicle might need a new flywheel:

An unusual vibration or pulsing felt in the clutch pedal

The clutch “slips” during acceleration

Chattering or shaking when you engage the clutch

The transmission pops out of gear while you are driving

This text is only for demo


How does a technician perform A Flywheel Replacement ?

Flywheel replacement is a fairly involved process. It requires complete removal of the transmission from your vehicle, among other things. If the service is being done at the same time that your clutch is being replaced, the added labor is not extensive.

To replace your engine flywheel, a technician will first need to lift and support your vehicle in the air for access. From there, the following general steps are performed:

  • Remove any shields and guards for access
  • Disconnect and remove the driveshaft
  • Remove the transfer case (if so equipped)
  • Unbolt the transmission from the engine and remove the transmission from the vehicle
  • Disassemble the clutch assembly and remove it from the flywheel
  • Unbolt and remove the flywheel Reassembly occurs in roughly the reverse order of disassembly, with a few exceptions. One exception is the need to bleed the clutch slave cylinder of air after the system is refilled with hydraulic fluid. Special alignment tools and procedures may be required to properly reassemble and install the clutch assembly. Any fluid lost must also be topped off.

Other Questions Customers Ask

What causes a flywheel to fail?
A flywheel may fail due to overheating from exceeding a vehicle's rated towing capacity or overloading it past the GVWR. This leads to additional stress on the drivetrain, which ultimately can warp or crack the flywheel. Aggressive use of the clutch can also cause excessive wear to the flywheel.
How long should a flywheel last?
A flywheel should last 80K miles or more. The truth is, the lifespan of a flywheel - or any components related to the clutch in a vehicle with a manual transmission - is almost entirely dependent on driving habits. Aggressive use of the clutch, hauling heavy loads, or pulling a trailer that exceeds the manufacturer’s recommendation can all limit the life of a flywheel. On the other hand, if proper care is taken, a flywheel could last the lifetime of the vehicle.
Can you drive with a damaged flywheel?
Although you can sometimes drive with a damaged flywheel, this will often lead to more serious damage to surrounding components. If a flywheel is warped and vibrating, for example, it could ruin the engine crankshaft or rear main bearing in the engine - which is far more expensive to replace than just a flywheel.

This is demo Question

This is demo Answer

Compare discounted prices at 32k+ shops.

Finding a trusted shop has never been easier. We've partnered with the largest brands in auto maintenance to give our customers the biggest network to choose from.

PepBoys Full SVG
Firestone Name SVG
Jiffy Lube Full SVG
NTB Logo SVG 1
Discount Tire Full SVG
GoodYear Logo Full SVG 1
Valvoline Name SVG
Meineke Name SVG

Trusted & partnered with leading companies.

We've earned a reputation as the go-to choice for quality car care, with some of the biggest names in business reaping the benefits and improving their customer's car care experience.


Need to talk about something?

Call us at (844) 923-8473 or email [email protected]

Join the world's largest consumer fleet.

Over 1.8 Million already have.