An Ignition Control Module Replacement costs by shop in Marietta.
CarAdvise Customers save an average of $121 on An Ignition Control Module Replacement.
Average cost of An Ignition Control Module Replacement for popular vehicle models in Marietta:
Avg. cost $650
Chevrolet Silverado 1500
Avg. cost $144
Dodge Grand Caravan
Avg. cost $765
THE IMPORTANCE OF An Ignition Control Module Replacement
What is an ignition control module and how does it work?
An ignition control module is a small onboard computer used in many older vehicles to control when the spark plugs engage or “fire” inside the engine. This control module relies on data from components such as the crankshaft position sensor, camshaft position sensor, and throttle position sensor to determine the proper timing for the spark plugs and to optimize engine efficiency and power. Many newer vehicles do not have an ignition module. Instead, spark plug timing is controlled by the engine control module (ECM).
How do I know if my vehicle needs the ignition control module replaced?
If the ignition control module malfunctions, the symptoms that result can mirror those of the components that it controls, namely the coil(s), distributor cap, spark plugs, and spark plug wires. If your vehicle has an ignition module that goes bad, you might notice the following symptoms:
Your engine sputters, lacks power, and/or stalls
The engine backfires or afterfires (backfires once it has been shut off)
Your vehicle will not start
Your vehicle fails an emissions test
This text is only for demo
FREQUENCY OF INSPECTION
How does a technician perform An Ignition Control Module Replacement ?
An ignition control module is usually located somewhere in the engine compartment, either on the engine, the distributor assembly, or the firewall (the panel that separates the engine from the passenger compartment).
To replace the ignition control module, a technician will take the following general steps:
Disconnect the negative battery terminal to cut power to the vehicle
Remove any shields, guards, covers, or ducts necessary to gain access to the engine control module
Disconnect the electrical wiring from the ignition control module
Unfasten the mounting screws or hardware
Remove the module and install a new on in its place
Re-attach the mounting screws and reconnect the wires
Reinstall the shields, guards, covers, or ducts that were removed
Most ignition control modules do not need to be programmed after installation, but a technician will need to verify that it is working properly by running and test driving your vehicle. The location of the module and wires on some vehicles require access from below the vehicle and can make the service more difficult to perform.
OTHER QUESTIONS CUSTOMERS ASK
Is an ECU the same as an ignition control module?
No, the ECU (Engine Control Unit) or ECM (Engine Control Module) is a computer that controls a variety of engine functions, including timing, air/fuel mixture, and more. It interprets data from an array of sensors and uses that information to help your engine run efficiently and at peak performance. An ignition control module, on the other hand, guides only the ignition timing on (mostly) older engines.
What causes ignition module failure?
Heat is the most common contributor to ignition control module failure. Not only does the engine compartment contain a good deal of heat from the engine and exhaust system, but, on many older vehicles, an aging distributor assembly can cause excessive heat and affect the module.
Where is the ignition control module located?
An ignition control module is often mounted on the distributor assembly near the back of an engine. It might also be located elsewhere on the engine or on the firewall that separates the engine compartment from the passenger compartment.
This is demo Question
This is demo Answer
Compare discounted prices upfront at over 26,000 shops nationwide.
Finding a trusted shop has never been easier. We've partnered with the largest brands in auto maintenance to give our customers the biggest network to choose from.
Our digital platform is designed to make maintaining and repairing your vehicle a breeze – from conveniently scheduling services, finding shops in the area, approving work remotely or getting free expert advice so you can be confident about any decision.
How much does CarAdvise cost?
There’s nothing to pay up-front; you simply only pay for repairs or services that you approve.
Are there any additional fees?
Nope, no funny business here—just get the job done and pay for what you approve. It really is that simple.
Are there shops available in my area?
With our handy nationwide network of over 26,000 shops to choose from and free sign-up – you can rest assured your car is in good hands.
How does CarAdvise pricing work?
With CarAdvise, you don’t need a fleet of 100,000 cars to get an amazing deal on car services. Our discounted prices are guaranteed to beat any other retail options – so why spend more? On average customers save 15-40% when they choose us – that could mean hundreds saved in just one service job.
At CarAdvise, we believe life is unpredictable and if you need to reschedule or cancel an appointment – no worries! We promise there’s never any penalty for missed appointments.
What shops do you work with?
We’ve partnered with the best in the industry such as Firestone, Pep Boys, JiffyLube, Canadian Tire, NTB, Meineke, Tire Kingdom, AAMCO, Monro, FCA dealerships and many independent shops across the country.
How do I sign up?
Ready to join the party? Just a few clicks and you’ll be all set – create your account now. You can easily create your account here.
How do I get more help?
Just email us at [email protected] or give our friendly team a ring at (844) 923-8473 and we’ll be sure to lend you the helping hand you need.