Find 400+ services from a network of trusted shops and book appointments in seconds.
Approve
Approve or decline an itemized list of services and costs before any work begins.
Pay
Pay securely and enjoy exclusive discounted rates and a hassle-free checkout experience.
AVERAGE COST IN Westland
An Ignition Control Module Replacement costs by shop in Westland.
CarAdvise Customers save an average of $122 on An Ignition Control Module Replacement.
POPULAR VEHICLES
Average cost of An Ignition Control Module Replacement for popular vehicle models in Westland:
Car Model
Avg. cost
$50
Maintenance as it's meant to be.
Transparent
Never overpay for car maintenance. Compare and select from discounted prices across 26,000+ trusted shops nationwide.
Empowering
Ignite your auto knowledge. Gain invaluable insights into maintenance schedules, service clarity, and obtain expert advice.
Hassle-Free
Bypass the stress of negotiations. CarAdvise simplifies your car care journey for an effortless experience.
THE IMPORTANCE OF An Ignition Control Module Replacement
What is an ignition control module and how does it work?
An ignition control module is a small onboard computer used in many older vehicles to control when the spark plugs engage or “fire” inside the engine. This control module relies on data from components such as the crankshaft position sensor, camshaft position sensor, and throttle position sensor to determine the proper timing for the spark plugs and to optimize engine efficiency and power. Many newer vehicles do not have an ignition module. Instead, spark plug timing is controlled by the engine control module (ECM).
COMMON SYMPTOMS
How do I know if my vehicle needs the ignition control module replaced?
If the ignition control module malfunctions, the symptoms that result can mirror those of the components that it controls, namely the coil(s), distributor cap, spark plugs, and spark plug wires. If your vehicle has an ignition module that goes bad, you might notice the following symptoms:
Your engine sputters, lacks power, and/or stalls
The engine backfires or afterfires (backfires once it has been shut off)
Your vehicle will not start
Your vehicle fails an emissions test
This text is only for demo
FREQUENCY OF INSPECTION
How does a technician perform An Ignition Control Module Replacement ?
An ignition control module is usually located somewhere in the engine compartment, either on the engine, the distributor assembly, or the firewall (the panel that separates the engine from the passenger compartment).
To replace the ignition control module, a technician will take the following general steps:
Disconnect the negative battery terminal to cut power to the vehicle
Remove any shields, guards, covers, or ducts necessary to gain access to the engine control module
Disconnect the electrical wiring from the ignition control module
Unfasten the mounting screws or hardware
Remove the module and install a new on in its place
Re-attach the mounting screws and reconnect the wires
Reinstall the shields, guards, covers, or ducts that were removed
Most ignition control modules do not need to be programmed after installation, but a technician will need to verify that it is working properly by running and test driving your vehicle. The location of the module and wires on some vehicles require access from below the vehicle and can make the service more difficult to perform.
Other Questions Customers Ask
Is an ECU the same as an ignition control module?
No, the ECU (Engine Control Unit) or ECM (Engine Control Module) is a computer that controls a variety of engine functions, including timing, air/fuel mixture, and more. It interprets data from an array of sensors and uses that information to help your engine run efficiently and at peak performance. An ignition control module, on the other hand, guides only the ignition timing on (mostly) older engines.
What causes ignition module failure?
Heat is the most common contributor to ignition control module failure. Not only does the engine compartment contain a good deal of heat from the engine and exhaust system, but, on many older vehicles, an aging distributor assembly can cause excessive heat and affect the module.
Where is the ignition control module located?
An ignition control module is often mounted on the distributor assembly near the back of an engine. It might also be located elsewhere on the engine or on the firewall that separates the engine compartment from the passenger compartment.
This is demo Question
This is demo Answer
Compare discounted prices at 32k+ shops.
Finding a trusted shop has never been easier. We've partnered with the largest brands in auto maintenance to give our customers the biggest network to choose from.
We've earned a reputation as the go-to choice for quality car care, with some of the biggest names in business reaping the benefits and improving their customer's car care experience.
