Diagnostic Trouble Code P0124

P0124 “Throttle/Pedal Position Sensor/Switch A Circuit Intermittent”

 

What is code P0124?

Code P0124 stands for “Throttle/Pedal Position Sensor/Switch A Circuit Intermittent”. This diagnostic trouble code can show up for a number of reasons that have to do with the throttle position sensor and accelerator pedal position sensor. Therefore, it is important to have a qualified technician diagnose the specific problem that caused the code to be stored in your vehicle’s computer.

Get this checked out soon by a CarAdvise shop, where the work will be guaranteed, and one of our expert techs will review any repair orders.

What does code P0124 mean?

Code P0124 on a diagnostic scan of your vehicle tells a technician that there is something going on with one of the sensors that enables the throttle on your engine.

On older vehicles, a cable connected the accelerator pedal inside the passenger compartment to the throttle body (or the carburetor) on an engine. There was a physical connection between the pedal under the driver’s foot and the throttle. Today’s automobiles, however, feature a system of sensors that control throttle operation. One sensor, the accelerator pedal position (APP) sensor (mounted on the accelerator pedal assembly), detects how far you press the gas pedal. The throttle position sensor (TPS) is mounted on the throttle body on your engine and detects how far the throttle plate is open. It is not uncommon for an engine to rely on two throttle position sensors.

Together, the APP sensor and TPS work to deliver data from the accelerator pedal and the throttle body to the ECM (Engine Control Module). When you press the accelerator pedal, the information is sent to the ECM which, in turn, controls the throttle body and other functions. This arrangement is termed “drive-by-wire” technology. Whenever your engine is running, data from these sensors is sent continuously to the ECM. The data should mirror what the driver is commanding through the accelerator pedal. The ECM uses the data to determine how much power the engine should be making. This correlates to how far the throttle plate opens (in combination with the throttle position sensor), how much fuel is injected into the cylinders, when the spark plugs are fired, and more.

Code P0124 is triggered when the ECM senses that the voltage from the throttle/pedal position sensor/switch “A” circuit is outside of its normal range, intermittent, and unreliable.

 

What causes code P0124?

A number of causes can trigger a code P0124. That is why an accurate diagnosis is essential. Causes of this code include:

Most likely

Other possibilities

  • Corrosion on the sensor connector or ECM connector
  • Torn or jammed floor mats
  • Bad ECM

 

What symptoms are associated with this code?

Common signs associated with a code P0124 include the following:

  • The check engine light is on or flashing
  • Vehicle is hard to start
  • Engine runs roughly or hesitates on acceleration
  • Your engine enters “limp” mode and will not accelerate
  • Engine idles higher than normal
  • Transmission shifts incorrectly

 

How does a technician diagnose code P0124?

If a diagnostic scan of your vehicle indicates a code P0124, a technician will perform tests to pinpoint the problem. These tests include checking for any related trouble codes. The technician will manually press the pedal with the engine off. In the meantime, he will use the scan tool to view live data from the APP sensor to determine whether or not it is consistent. The wiring from the ECM to the sensor will be inspected for cracks, corrosion, contamination, or bent pins on the connectors. The technician might also perform tests on the APP sensor or TPS with a multimeter and verify that adequate voltage is reaching the sensor when it is in operation.

 

How serious is this code?

In some cases, you might not notice any symptoms when a code P0124 is present. Otherwise, symptoms might be intermittent. If your vehicle is placed by the ECM into failsafe “limp” mode, you will be unable to accelerate. The engine might run roughly. This problem should be addressed as soon as possible.

Get this checked out soon by a CarAdvise shop, where the work will be guaranteed, and one of our expert techs will review any repair orders.

 

Related Diagnostic Trouble Codes

P0120 Throttle/Pedal Position Sensor/Switch A Circuit

P0122 Throttle/Pedal Position Sensor/Switch A Circuit Low

P0123 Throttle/Pedal Position Sensor/Switch A Circuit High

 

Get expert advice, find shops, schedule, approve, & pay for any service.

Guaranteed to be lower than in-store retail price.

Transparent Pricing

Never overpay for car maintenance. Compare and select from discounted prices across 26,000+ trusted shops nationwide.

Empowerment

Ignite your auto knowledge. Gain invaluable insights into maintenance schedules, service clarity, and obtain expert advice.

Hassle-Free

Bypass the stress of negotiations. CarAdvise simplifies your car care journey for an effortless experience.

Peace of Mind

Rest easy knowing you're getting quality service at the right price, without any hidden costs or surprises.